Original Electronic Components is important!


components (3)


It’s important to ensure the products quality during the PCBA processing, not only control
the processing process, but also control the components from sourcing, to ensure that the
electronic components are original authentic. Now there are some unscrupulous businessmen
through the purchase of counterfeit brand components on the market, and then sell with high
profits, resulting in some of the PCBA factory damage.So how to ensure the electronic
components are the original?

Electronic Components

To ensure that the electronic components in the PCBA machining process is original, below
are 2 ways to identify them.

1.the qualification of agent

Now,electronic components agents, trade quotient numerous, quality and price level in the
sales maket is uneven, to ensure that the electronic components of the original authentic,
which can through the enterprise’s official website to see whether there is an agent with
qualification, and purchased through formal channels.

Generally, agents have the qualification and controled by the original factory, to ensure
that the source of electronic components is original

2. reputation and credibility

Generally, the distributors and traders are in good reputation and credibility, their
components are not bad. Because an enterprise’s reputation and credibility of the
accumulation is to go through a very long time, accompanied by recognized brand
manufacturers, basically their components are not counterfeit.

Three/incoming inspection of material

In addition to the above two steps, there is a very important step is the incoming
inspection of components.The normal PCBA processing manufacturers to just buy the
components with incoming inspection, sampling components or full inspection, to ensure the
quality of the components.

When sourcing the electronic components, need to be ware of the top mark,the production
batch number, and other related components to beta appearance and physical details, in
order to ensure that the electronic components is the original authentic.

tmliir Jun 07, 2017 Component, FPC, PCB, PCBA&SMT&PCB Assembly 0 Comment Read More

The key points of FPC assembly, and details need to know about the Flexible PCBA

FPC assembly, Flexible PCBA-Bright PCB China FPC assembly factory







Abstract: In the trend of miniaturization of consumer electronic products, FPC is more and more widely used.

The FPC SMT process is different from the Rigid PCB. This post describes details of the FPC SMT preprocessing, Printing, SMT,
reflow, testing, sub-board processes and other key points. Bright PCB Technology is a China FPC assembly factory,
manufacturing Flexible PCBA for years, owned high reputation in this industry.

PCB is printed circuit board, referred to as Rigid board. FPC is flexible circuit board, also known as flexible circuit board or
flexible circuit, referred to as Flex PCB. The miniaturization of electronic products is an inevitable trend, a considerable
number of consumer products, surface mount, due to the relationship between the assembly space, the SMD are
mounted on the FPC to complete the assembly of the machine, FPC in the calculator, mobile phones, digital cameras ,
Digital cameras and other digital products have been widely used in the FPC on SMD surface mount SMT technology has
become one of the trends.
FPC surface SMT process’ solution is differ from the traditional Rigid PCB SMT in many details, in order to do FPC SMT
technology, the most important thing is positioning. FPC board’s hardness is not enough, softer, if you do not use a
dedicated carrier board, you can not complete the fixed and transmission, it can not complete printing, SMT, furnace and
other basic SMT processes. Following FPC SMT production on the FPC pretreatment, fixation, printing, SMT, reflow,
testing, testing, sub-board processes, such as key points were detailed.
1. FPC pretreatment
FPC board is soft, the factory is not generally vacuum packaging, in the transportation and storage process is easy to
absorb moisture in the air, to be cast in the SMT line before the pre-baking treatment, the water slowly forced discharge.
Otherwise, the reflow soldering under high temperature impact, FPC absorption of water vaporization quickly become
prominent FPC, easily lead to FPC delamination, blistering and other undesirable.

Pre-baking conditions are generally 80-100 ℃ temperature 4-8 hours, under special circumstances, you can increase the
temperature to 125 ℃ or more, but the corresponding shortening baking time. Before baking, be sure to make a small
sample test to determine if the FPC can withstand the set baking temperature, or consult the FPC manufacturer for
appropriate baking conditions. Baking, FPC stacking can not be too much, 10-20PNL more appropriate, and some FPC
manufacturers will put a piece of paper between each PNL to be isolated, to be sure that this separation of the paper can
withstand the set baking Temperature, if you do not need to take out after the separation of paper, and then baking. After
baking the FPC should be no obvious discoloration, deformation, from Alice and other undesirable, subject to the IPQC
sampling qualified to vote.

2. Special carrier board production
According to the CAD file of the circuit board, read the hole positioning data of the FPC to manufacture the high precision
FPC positioning template and the special carrier plate, make the diameter of the positioning pin on the positioning
template and the positioning hole on the carrier plate, the hole diameter of the positioning hole on the FPC match. Many
FPC because to protect part of the line or the design of the reasons is not the same thickness, and some places thick and
some places thin, and some have to strengthen the metal plate, so the board and the FPC at the junction of the need to
press The actual situation for processing grinding groove, the role is in the printing and placement to ensure that the FPC
is flat. Material requirements of thin plate, high strength, less heat absorption, heat quickly, and after several thermal
shock after warping small. Commonly used carrier plate materials are synthetic stone, aluminum, silica gel plate, special
high temperature resistant magnetized steel plate.

Ordinary carrier board: common carrier board design is convenient, proofing fast. Commonly used ordinary carrier
material for the engineering plastics (synthetic stone), aluminum, etc., engineering plastic carrier life of 3000-7000 times,
easy to operate, good stability, not easy to absorb heat, not hot, the price is 5 times the aluminum the above. Aluminum
carrier board heat absorption fast, no temperature difference between inside and outside, deformation can be simple
repair, cheap, long life, the main drawback is hot, to use insulated gloves to send.

Silicone sheet: The material has a self-adhesive, FPC directly on the stick, without tape, but also easier to remove, no
residual glue, and high temperature. Silicone sheet in use, the use of chemical process, the use of silica gel material in the
process of aging will decline in viscosity, viscosity during use will be less clean, life expectancy is short, up to 1000-2000
times, the price is relatively high.

Magnetic fixture; special high temperature (350 ℃) to strengthen the magnetization of steel processing to ensure that the
process of reflow soldering, good elasticity, good flatness, high temperature deformation. Because the strengthening of
the magnetic properties of the steel sheet has been pressed flattened FPC surface, FPC reflow soldering in the reflow
soldering to avoid the bad welding, to ensure the welding quality and improve yield. As long as not man-made damage
and accident damage can be permanently used, long life. Magnetic fixture at the same time on the FPC for thermal
protection, the board will not have any damage to the FPC. But the magnetic fixture design complexity, high unit price,
mass production only a cost advantage.

3. production process
Here we take the common carrier board as an example to describe the FPC SMT points, the use of silica gel plate or
magnetic fixture, FPC to facilitate a lot of fixing, without the use of tape, and printing, patch, welding process is the key
points the same.

1). Fixation of FPC:
Prior to SMT, you first need to accurately FPC fixed on the carrier board. In particular, the shorter the storage time
between printing, mounting and soldering, the better the FPC is fixed to the carrier board.

Carrier plates are available with locating pins and without locating pins. Without positioning pins of the carrier plate, with
the positioning pin with the positioning template supporting the use of the first set of carrier plate in the template of the
positioning pin so that the positioning pin through the positioning hole on the carrier plate exposed FPC will be a set in the
Exposed to the positioning pin, and then tape fixed, and then let the carrier board and FPC positioning template
separation, printing, patch and welding. With the positioning pin on the carrier plate has been fixed about 1.5mm spring
pin number, you can FPC one piece directly on the carrier plate spring locating pin, and then tape fixed. In the printing
process, the spring pin can be completely pressed into the stencil board, will not affect the printing results.

Method 1(single-sided tape fixed): with a thin high-temperature single-sided tape will be fixed on the FPC board on the
four sides, not to offset and Qiao FPC, tape viscosity should be moderate, easy to peel after reflow, and FPC No residual
glue. If you use automatic tape machine, can quickly cut the length of the same tape, can significantly improve efficiency,
cost savings, to avoid waste.

Method 2 (double-sided adhesive tape): first with high-temperature double-sided tape attached to the carrier board, the
effect and silica gel plate, and then paste the FPC to the carrier plate, pay special attention to tape viscosity can not be too
high, or reflow after stripping , It is likely to cause FPC tear. After repeated oven over and over, the viscosity of double-
sided tape will gradually become low, low viscosity can not be reliable fixed FPC must be replaced immediately.

This station is to prevent FPC dirty focus of the station, need to wear finger sets of operations. The carrier board should
be cleaned properly before being reused. It can be cleaned with a non-woven cloth dipped in a cleaning agent, or an anti-
static dust roller can be used to remove dust and tin beads. Take FPC should not be too Rigid, FPC is more fragile, prone to
crease and fracture.
2). FPC solder paste printing:
FPC on the composition of the solder paste is not very special requirements, the size of the solder ball particles and metal
content to FPC, there is no fine pitch IC shall prevail, but the FPC on the solder paste printing performance requirements
are higher, solder paste should have excellent Thixotropy, solder paste should be able to easily release the mold and can
be firmly attached to the FPC surface, will not appear mold release obstruction bad stencil or printing after the collapse.

Because the loading board FPC, FPC positioning with the high temperature tape, so that the plane is inconsistent, so FPC
printing surface can not be as flat as the PCB and the thickness of the Rigidness of the same, it is not appropriate to use
metal scraper, but should be used in Rigidness 80 -90 degrees of polyurethane-type scraper.

Paste printing machine with the best optical positioning system, otherwise there will be a greater impact on the print
quality, FPC although fixed on the carrier board, but between the FPC and the carrier board will always produce some
small gap, which is Rigid with the PCB The biggest difference between the board, so the device parameters set the printing
effect will have a greater impact.

Printing station is to prevent the FPC dirty focus of the station, you need to wear finger sets of operations, while
maintaining the cleanliness of the workplace, ground rubbing steel mesh to prevent solder paste pollution FPC gold finger
and gold-plated buttons

3). FPC patch
According to the characteristics of the product, the number of components and chip efficiency, the use of medium-speed
placement machine, high-speed placement machine can be mounted. Because each piece of FPC has the positioning of the
optical MARK mark, so the SMD mount on the FPC and PCB placement is not very different. Note that, although the FPC is
fixed on the carrier board, but its surface can not be as flat as the PCB Rigid board, FPC and the board will certainly exist
between the local gap, so the nozzle drop height, blowing pressure Need to be set accurately, the nozzle moving speed to
be reduced. At the same time, FPC to the majority of the board, FPC yield is relatively low, so the whole PNL contains
some bad PCS is normal, which requires placement machine with BAD MARK recognition, otherwise, in the production of
such non-whole PNL is a good board case, the production efficiency will be greatly reduced.

4). Reflow soldering of FPC
The use of forced convection hot air convection oven, so that the temperature on the FPC can be more uniform changes
in the production of welding to reduce the bad. If the use of single-sided tape, because only fixed FPC’s four sides, the
middle part of the deformation in the hot air state, the pad is easy to form tilt, melting tin (high temperature liquid tin) will
flow and empty welding, Tin beads, so that a higher rate of non-performing process.

A) Temperature curve test method:
Due to the different heat absorption of the carrier plate and the different types of components on the FPC, the
temperature rise rate during the reflow process is different and the heat absorption is different. Therefore, the
temperature profile of the reflow oven is carefully set, Great influence. The more reliable method is based on the actual
production of the carrier board spacing in the test board before and after the release of the two FPC equipped with the
carrier board, while the test board FPC mounted components, high temperature solder wire test temperature The probe
is welded to the test point, and the probe wire is fastened to the carrier plate with a high temperature tape. Note that high
temperature tape can not cover the test points. Test points should be selected in the vicinity of the solder pad on the side
of the carrier board and QFP pins, etc., such test results better reflect the real situation.
B) The temperature curve settings:
In the furnace temperature debugging, because the FPC temperature is not good, so it is best to use temperature /
temperature / return curve of the temperature curve, so that the parameters of the temperature zone is easy to control
some other FPC and components of the impact of thermal shock should be small some. According to experience, it is best
to adjust the furnace temperature to the lower limit of the technical requirements of solder paste, back to the furnace of
the wind speed are generally used by the furnace can use the minimum wind speed, back to the furnace chain stability is
better, can not shake.

5). FPC inspection, testing and sub-board:
As the carrier plate in the furnace endothermic, especially the aluminum carrier plate, baked when the temperature is
higher, it is best to increase the forced cooling fan in the mouth to help rapid cooling. At the same time, the operator must
take insulated gloves, so as to avoid burned by high temperature carrier board. FPC from the carrier board to complete
the welding, the force should be uniform, can not use brute force, so as to avoid the FPC is torn or crease.
Remove the FPC on the SMT magnifying glass over 5 times under the visual inspection, focusing on checking the surface
of residual plastic, discoloration, gold finger dip tin, tin beads, IC pins with soldering and other welding problems.
Because the FPC surface can not be very flat, so that the false positive rate of AOI is high, so FPC is generally not suitable
for AOI inspection, but by using a dedicated test fixture, FPC can complete ICT, FCT test.
FPC to the majority of the board, may be ICT ICT, FCT test before the need to do sub-board, although the use of blades,
scissors and other tools can also be completed sub-board operations, but operating efficiency and low quality, high scrap.
If it is shaped FPC mass production, it is recommended to create a special FPC stamping sub-module, the stamping
division, can greatly improve the efficiency of work, while punching out the edge of the FPC neat appearance, punching
board generated when the internal stress is low, Can effectively avoid solder joints crack.
4. summary
SMD on the FPC, the precise positioning and fixation is the key points, the key of fixing is to produce the appropriate
carrier board. Then the FPC pre-baking, printing, patch and reflow. Apparently the FPC SMT process is much more difficult
than PCB Rigid board, so the precise setting of process parameters is necessary, at the same time, strict production
process management is also important to ensure that operators strictly enforce the SOP on each of the provisions, with
the line Engineers and IPQC should strengthen the inspection, the timely detection of abnormal production lines, analyze
the reasons and take the necessary measures to the FPC SMT production line to control the quality of FPC assembly.

Bright PCB Technology is a China FPC assembly manufacturer, offers FPCBA prototy and mass producing of Flexible PCBA,
if need FPC or Flexible PCB assembly please Contact US!

Copyright Notice: All images and text on this site are protected by copyright. Can be used ONLY by written authorization
with signature and stamp.

tmliir Oct 16, 2016 FPC, PCBA&SMT&PCB Assembly 0 Comment Read More

The differences need to know between the FPC assembly and Rigid PCB assembly


The differences need to know between the FPC assembly and Rigid PCB assembly

Ordinary SMT processing is basically the same, because the flexible circuit board, Rigid-Flex board and Rigid board all need the component placement and reflow soldering paste welding process. However,as to the Flexible PCBA and Rigid PCBA there is some details specially, if the extra details are not handled properly, then there will be tremendous problems.

Then, let’s move to the details as follow:
1. solder paste welding process
Just like the Rigid PCB assembly process, using the stencil and the solder paste to cover the Flexible Printed Circuit Board and Rigid-Flex PCB with solder paste. Many SMT workers are troubled by the size and the fragileness, differ from the Rigid PCB, the surface of Flexible PCB is not smooth, then need some fixtures and positioning holes to fix. Moreover, the FPC material is not dimensionally stable and will stretch or fold by 0.001 degrees per inch as a function of temperature and humidity changing. More interestingly, these stretching and wrinkling factors will result the FPC displacement in the X and Y directions. Due to this, the FPC assembly requires smaller carriers comparing to the Rigid PCBA.

2. SMT components placement
Under the trending of miniaturization of components, tiny components in the reflow process happens to some problems. If the line width of FPC is narrow, stretching and wrinkling will not be a significant problem, it need a smaller SMT carrier or additional Mark points. The carrier is not smooth also leads to displacements. SMT fixture is the main reason to keep the FPC SMT surface smooth.

3. reflow process
Before reflow soldering, the Flexible PCB must be dry, this is the main differece between the Flexible Circuit board SMT and Rigid Circuit board SMT. Besides the instability of the FPC materials, they are also hygroscopic and absorb moisture (up to 3% by weight) like sponges. Once the FPC absorbs moisture, it has to stop the flowing. Rigid PCB also has the same problem, but Rigid PCB has a high tolerance. Flex PCB require a preheat bake up to 225°-250 ° F, this process need to finish quickly within 1 hour. If it is not baked in time, then needs to be stored in a dry or nitrogen storage compartment.

We Bright PCB Technology a China FPC aseembly factory always cares about all the details above.Work with us to produce more excellent products. You are warmly welcome to CONTACT US!

Copyright Notice: All images and text on this site are protected by copyright. Can be used ONLY by written authorization with signature and stamp.

tmliir Jun 08, 2015 FPC, PCBA&SMT&PCB Assembly 0 Comment Read More

PCB Engineering Question-EQ

PCB-EQ-Engineering Queation

PCB Engineering Question-EQ

There is always details need to confirm before producing the PCB. To avoid mistakes, cut the cost, DFM(design for manufacturing), EQ is a result of total checking the file and to confirm the final producing file.

Usually may come across these situations.

The Raw file data itself was flawed and exception, data processing while
others are more likely to be found, but when it comes to network
connectivity defect, it is difficult to check it out.

For example:
a normal line break
Process does not match the design requirements with the Gerber
Actual number of aperture, hole, holes drilled document properties with
hole diagram marking inconsistencies
Etched fonts with screen printing characters overlap
In order to optimize production costs and shorten the production cycle
and improve efficiency, enhance the quality of products, works in
accordance with the factory process capability and process, proposals to
modify or adjust the original Design materials.

For example:
canceling two-sided character is changed to single characters
On the PCS added Gong positioning pins
Green oil bridge IC pad to cancel change through Windows ‘ production
Through-hole tapped hole to cover the oil or modified Windows.

This Process is important and necessary, it helps doing the right fabrication.

tmliir May 12, 2015 FPC, PCB 0 Comment Read More

FPC Prototype, Flex PCB Prototype, Flexible Circuit Prototyping

We Bright PCB Technology has years of producing FPC, with our experienced guys serves hunders of clients who need Flexible Circuit Board. Our products including the Single layer FPC, double sided FPC, and multilayer FPC, moreover, many clients need the FPC assembly, that is most of the SMT factory not familiar with. Fortunately this is our advantage, 80% of our FPC clients chose us to finish the FPC assembly, because we take care of every single detail about the processes of FPCBA.

Single layer FPC is most using in the lighting industry and display industry as a light provider device’s part. We take very care about the feature of these industries, the stableness, long life span, proper conductivity are the main features of the FPC used in lighting and display. A pic of our product below:



FPC prototyping means fast producing, quick test and immediately delivery.

With our professional equipment, we can efficiently do the drilling, PTH, lines, etching, etc. And applied the flying probe machine, fast test is available. FPC prototype in 3 days is abusolutely ok for us, and this service helped our client faster their product exploring.

And self-owned lines of surface treatment helps us to control the quality of OSP, ENIG on the surface of Flexible Circuit Board.

If need FPC prototype including Single layer FPC, Double sided FPC or Multilayer FPC, pls contac us immediatly! Also FPC assembly is available. Know more about the FPC assembly pls view this post: The differences need to know between the FPC assembly and Rigid PCB assembly

Copyright Notice: All images and text on this site are protected by copyright. Can be used ONLY by written authorization with signature and stamp.


tmliir Jun 19, 2014 FPC, PCB 0 Comment Read More

RFQ of PCB Fabrication


6 layer Rigid-Flex-PCB, China 6 layer Rigid-Flex-PCB, China Rigid-Flex-PCB Factory, China 6 layer Rigid-Flex-PCB Manufacturer, FPC Assembly, China FPC Assembly Factory, China FPC Assembly Manufacturer, China FPC Factory, China FPC Manufacturer, PCB, FPC, PCBA, PCB Assembly, Copper Base PCB, Heavy Copper PCB


PCB Fabrication is our basic product and services. From the very start of Schematic, layout, you can just send file about your needs, we will do the rest. Then Prototype and low volume fabrication, and the massive production are all available here.


We do the Rigid PCB, FPC(Flex PCB), Rigid-Flex PCB, HDI, Aluminum PCB, Copper base PCB, Ceramic PCB, and HF PCB.

Best send us the Gerber file. Pls note us about specification of your needs as below:



Board Size:



Copper Weight:

Solder Mask Color:

Silk Screen Color:


Surface treatment:



Some tips about cost saving of PCB Design:

1. Use the most applied solder mask color: green

2. Silk screen as White

3. Panelization of your PCB

tmliir May 12, 2014 FPC, PCB 0 Comment Read More

What is Flexible Printed Circuit (FPC)-Materials

The Materials of Flexible Printed Circuit (FPC)

Mainly consisted with 4 parts: Copper Film, Cover Film, PI Striffener Film, Adhesive Sheet

Specific materials involved are as below:

Copper: can be ED-Electro Deposit or RA-Rolled Annealed (which is usually used for the FPC for mobile). Usually 1oz or 1/2 oz thickness (copper thickness: 1/2oz =0.7 mil=0.018mm)
Base Film: normal material is PI (polyimide). Usually 1mil or 1/2 mil thickness.
Adhesive: thickness is up to customers’ request. usually epoxy resin thermosetting adhesive
Cover Film: Used for surface insulation. Normal material is PI (polyimide). usually 1mil or 1/2 mil thickness.
PI Stiffener Film: Enhance the mechanical strength of FPC. Usually 5mil or 9mil thickness.
Release Paper: To avoid the adhesive stained
Stiffener Material: Usually use PI, FR-4 and steel sheets
Adhesive sheet between layers: 1mil epoxy resin thermosetting adhesive

Note: 1mil =1/1000in=0.025mm. 1mim=40mil

So, for each single layer Flexible Printed Circuit (FPC), the thickness is about: 0.5mil cover film + 0.5mil adhesive + 1/2oz copper +
0.5mil adhesive + 0.5 base film = 2.7mil=0.0675mm

–Posted by Bright PCB Technology Co., Ltd

tmliir Sep 11, 2013 FPC, PCB 0 Comment Read More

What is Flexible Printed Circuit (FPC)-Brief Introduction

Brief Introduction of Flexible Printed Circuit (FPC)

As we all know that FPC is widely used in the mobile phones. It can connect the LCD and Mainboard, Side Key with Mainboard, which a normal rigid PCB can not achieve.
FPC, full name is Flexible Printed Circuit), is made of polyimide or mylar, an insulation material.
Flexible Printed Circuit (FPC) can be folded, bended freely. Besides, FPC is with very light weight, small volume, well heat dispersion, easy installation.
Flexible Printed Circuit (FPC), with it’s advantage of helping to make the electronic products with high density, now it’s widlely used in the area of aerospace, military, mobile communication, laptop, PDA, computer, camera, etc. Meanwhile Flexible Printed Circuit (FPC) also has some disadvantages, like not that durable, harder design and engineering, low possiblity of fix up, harder inpection, higher cost, etc. But these are not big problems compared with the advantages of Flexible Printed Circuit (FPC) can bring to us. That’s why it becomes more and more important and more often used in the electrics and telecommunication industries.

Structure of Flexible Printed Circuit (FPC)

Flexible Printed Circuit (FPC) can be single layer and multilayer.
Usually when we refer to the single layer FPC, it has only 1 layer of copper. But actually it has 5 layers (including adhesive, while the stiffiner not include), and normal double sided FPC has 1 inner layer (base film) with 1 layer of copper opn each side. But actually it has 9 layers (including adhesive, while the stiffiner not include).

–Posted by Bright PCB Technology Co., Ltd

tmliir Aug 17, 2013 FPC, PCB 0 Comment Read More

PCB&Assembly, FPC manufacturer China

China PCB, FPC manufacturer Bright PCB technology was established in 2003.
UL qualified in 2006.
ISO:2001 certificated in 2007.
ISO14001:2004 proved in 2008.
Also certificated by TS16949, ROHS, etc.

Specialized in the surface treatment industry, served other PCB factory to do the surface treatment like: ENIG, HASL, HASL-Lead free, Electric gold, OSP, etc. Bright PCB is a reputational manufacturer in south china area.

We kept the leadership in the past and now, and we will continiously contribute more value to this industry and our customers.

tmliir Jun 08, 2003 FPC, News, PCB 0 Comment Read More
  • Require RFQ of PCB, PCB Assembly?

    Contact us today!


  • Product Categories

error: Content is protected !!